
Sheet materials
Plywood, OSB, MDF and chipboard.
Sheet materials are timber in board form: plywood, film-faced plywood, OSB, MDF, chipboard and blockboard, bare or finished with melamine, HPL or veneer. Edge banding and veneer for finishing your own work come with them. You choose the board, the thickness and the finish, and we cut them to size.
The usual sizes are 1220 × 2440, 1250 × 2500 and 1220 × 3050 mm. Melamine and HPL boards also come in 1300 × 3050 and 2070 × 2800 mm. Thicknesses run from 3 mm for a cabinet back to 40 mm and more for heavy work.
Plywood is made of thin layers of wood glued crosswise on top of each other. That makes it strong, and it moves little. There is plywood in birch, poplar, okoume, pine and tropical hardwood, from 3 to 40 mm, and plywood with a face of oak, beech, maple or mahogany. For outdoor use or a damp room, choose plywood with a waterproof glue. Bending plywood is built so that you can curve it.
Film-faced plywood is plywood with a smooth, hard film on both sides. It is made for formwork, because concrete comes away from it easily. There is also film-faced plywood with a rough anti-slip pattern.
OSB is a board of large, pressed wood strands. It is strong but rough-looking, and is used mainly where it stays out of sight: as roof sheathing, subfloor or wall in timber-frame building. There is OSB/3 from 9 to 22 mm, sanded or unsanded, as a square-edged board or tongue and groove, so the boards slot into each other. There is also a fire-retardant OSB.
MDF is a board of fine, pressed wood fibres. The surface is smooth and the edges are dense, so it is easy to mill and paint: for cabinets, skirting boards and interior joinery. Standard MDF does not belong in a damp room; for that there is moisture-resistant MDF, also ready-primed in white. There is also MDF with veneer, melamine or HPL, black MDF, lightweight MDF and flexible MDF with grooves on one side.
Chipboard is made of small wood chips and glue, and is the base of most cabinets. Bare chipboard is brown. With a layer of melamine it becomes a melamine board: white, black, a plain colour or a wood decor. Furniture panels are narrower 18 mm melamine boards, 300 to 800 mm wide, with the long edges already finished. There are also tongue-and-groove chipboard panels for floors, and chipboard with HPL on both sides.
HPL is a thin, hard decorative sheet of less than a millimetre, which you glue onto a substrate, for example for a worktop or a cabinet front. The trade also calls it laminate, but it has nothing to do with laminate flooring. Compact HPL is a few millimetres thick and needs no substrate.
Blockboard has a core of strips glued side by side between two thin sheets: light and stiff, for long shelves and doors. There is also blockboard with a barnwood look. Hardboard is a thin, hard 3 mm fibreboard for cabinet backs and drawer bottoms; softboard is soft and light.
Veneer is a sheet of real wood, 0.6 to 1.4 mm thick, that you glue onto a board yourself, by the sheet, in oak, walnut, cherry, ash, elm, beech, padauk and afrormosia, among others. To finish the edges there is edge banding in ABS, a tough plastic, in melamine and in veneer, by the roll or by the length.
Boards are worked out by the piece, or in square metres (m²) when you are covering an area. For a quote, give us the type, thickness, finish and number of each board, and the sizes if we need to cut. A cutting list – the list of sizes and quantities – can also be a photo. Not sure which board suits? Call us and we’ll think it through with you.
Good to know
- Cutting service
- Send us your cutting list and we cut the boards to size.
- Moisture-resistant boards too
- Moisture-resistant MDF and plywood with waterproof glue.
- Finished boards
- Melamine, HPL and veneer, in colours and decors.
- Edge banding and veneer
- To finish edges and surfaces yourself.
Tell us what you need.
A question about sizes, quantities or prices? Send us a message or give us a call. We'll think it through with you.